You need to test, we're here to help.

You need to test, we're here to help.
Showing posts with label signal reflection. Show all posts
Showing posts with label signal reflection. Show all posts

14 February 2022

Transmission Lines for Oscilloscope Users, Part 4

Figure 1: Characteristic waveform when the source impedance is lower than the cable impedance.
Figure 1: Characteristic waveform when the source
impedance is lower than the cable impedance.
In Part 3, we saw the pattern of reflections that occur when both the source impedance and the oscilloscope input impedance are higher than that of the interconnect, and how those reflections affected the rise time measurement. Now let’s briefly consider what happens when the source impedance is lower than the impedance of the connecting cable. 

For this example, the source voltage is a 3.3 V square wave and the source impedance is 9 Ω. As before, our transmission line is a 50 Ω coaxial cable connecting the source to the oscilloscope. If the oscilloscope input termination is set to 1 MΩ, we see the interesting waveform shown in Figure 1.

31 January 2022

Transmission Lines for Oscilloscope Users, Part 2

Figure 1: A transmission line can be seen as a series of "buckets" of capacitance charged to a voltage by the signal as it "walks the line."
Figure 1: A transmission line can be seen as
a series of "buckets" of capacitance charged
to a voltage by the signal as it "walks the line."
In Part 1, we experimented with the signal rise time measurement and saw that it appeared to increase substantially as the length of the interconnecting cable was increased. To understand why, we revisited some basic principles of signal integrity:

1. All interconnects are transmission lines. 
2. Signals are dynamic, and once launched, cannot be prevented from propagating down the transmission line.

Be the Signal

To illustrate the dynamic nature of signals, imagine a very simple, 1 ns long, 50 Ω impedance transmission line. As a 1 V signal is launched into the transmission line and propagates, at each step along the way it asks "What's the impedance of the environment?" at its leading edge. That is the instantaneous impedance, notated as Z. Impedance is always defined as the ratio of a voltage to a current. We know the voltage of this signal (1 V), but how do we find the current at the edge? 

21 June 2021

Automotive Ethernet MDI S-parameter Testing

Figure 1: MDI S-parameter tests treat the Base-T1 pair as a balance transmission line and check that reflections don't cause either excessive power loss or mode conversion that can disrupt the signal.
Figure 1: MDI S-parameter tests treat the Base-T1
pair as a balance transmission line and check that
reflections don't cause either excessive power loss
or mode conversion that can disrupt the signal.
As said earlier, the automotive industry has very stringent EMC/EMI requirements, and all Automotive Ethernet standards are designed to ensure good operation even in the presence of high EMI. Not only is there the potential for interference from all the different electronic systems within the vehicle, nothing is stopping you from parking your vehicle below high-voltage transmission wires or in other high EMI fields. 

For this reason, all Automotive Ethernet standards have defined S-parameter tests to be performed at the Medium Dependent Interface (MDI). The assumption is that the single twisted pair that is the basis for all Base-T1 transmissions can be treated as a balanced, differential transmission line with some crosstalk. It is a very real-world application of S-parameters, which can seem so academic.

Two, mixed-mode S-parameters are measured at the MDI reference plane. The tests ensure that there is neither too much loss of power from reflections, nor too much mode conversion into differential signal, that it will disrupt the information of the PAM3 encoded signal.

19 December 2018

Using 50-Ohm Coax From DUT to Oscilloscope

A coaxial cable presents high impedance at low frequencies but acts as a transmission line at higher frequencies
Figure 1: A coaxial cable presents high impedance at low
frequencies but acts as a transmission line at higher frequencies
In our recent exploration of 10x passive probes, we've determined that while these types of probes are great general-purpose tools, they're not necessarily going to do the job in specialized measurement circumstances. They're relatively low-bandwidth, low-SNR probes that impose some limitations and, in some scenarios, can deliver potentially misleading or erroneous measurement results if used without clear understanding of their capabilities.

28 November 2018

10x Passive Probes and Cable Reflections

Figure 1: With unequal impedances at either end of the coax, are cable reflections a concern in 10x passive probes?
Figure 1: With unequal impedances at either end of the coax,
are cable reflections a concern in 10x passive probes?
We've been discussing the ubiquitous 10x passive probe here on Test Happens, beginning with an overview of the probe-oscilloscope system. We turned to the 10x passive probe itself and the issues posed by its constitutive circuitry. Then we covered what about that circuitry makes it usable at all, namely, its built-in equalization circuit.

19 June 2018

Rise-Time Degradation and ISI Jitter

Shown are the signals from two extreme bit patterns overlaid on top of each other with no interconnect in the channel
Figure 1: Shown are the signals from two extreme bit patterns
overlaid on top of each other with no interconnect in the channel
In discussing inter-symbol interference (ISI), the phenomenon in which information "leaks" from one bit to subsequent bits, we've identified a couple of root causes of ISI jitter. The first is reflection losses caused by impedance discontinuities, while the second is group delay dispersion, a consequence of the differing propagation speeds of different frequencies through a given material. We looked at these forms of distortion in both the time and frequency domains.

15 May 2018

Debugging DDR Memory on IoT Devices

Embedded systems such as IoT devices often require chip interposers to gain access to signal lines on DDR memory
Figure 1: Embedded systems such as IoT devices often require
chip interposers to gain access to signal lines on DDR memory
Internet of Things (IoT) devices are, at heart, just another embedded computing system, albeit one with an extremely well-defined function. As such, there's bound to be some amount of on-board data storage, and the storage medium of choice these days is typically double data-rate (DDR) memory. DDR memory transfers serial data on both the rising and falling edges of the clock signal, which is the characteristic from which it derives its name.

27 February 2018

Transmission Lines (Part IV): More Essential Principles

The return current in a transmission line is as important as the signal current
Figure 1: The return current in a transmission line
is as important as the signal current
In our continuing survey of the topic of transmission lines, we'd begun in our last post to cover some essential principles that govern their behavior. We're not quite done with those, so in this post we'll discuss more principles that should be part of the foundation of how you think about interconnects.

16 February 2018

Probing Techniques and Tradeoffs (Part XI): Non-Ideal Situations

VP@Rcvr builds a transmission-line model to virtually move less-than-ideal probing points
Figure 1: VP@Rcvr builds a transmission-line model
to virtually move less-than-ideal probing points
In using an oscilloscope to investigate transmission-line performance, we often encounter situations in which we don't have the luxury of probing at the ideal location. Fortunately, there are software tools that enable us to virtually move our probing point close to the receiver.