Setting Up Your Oscilloscope for ESD Pulse Testing

Figure 1: An ESD calibration test setup. 
The ESD gun discharges its waveform
into a properly attenuated current target. 

Electrostatic discharge (ESD) pulse tests are a type of conducted immunity testing done to confirm that a device can withstand a sudden transient electrostatic discharge. It is done by using an ESD gun to shoot a pulse of the required voltage at a device while testing that the DUT continues to operate properly. The ESD pulse shape simulates a person, carrying a static charge, touching a device. When their fingertip first touches the device, there is a leading edge with a high peak and fast decay, often visible in the real world as a spark flying from the fingertip. This is followed by a second edge due to the charge in the rest of the human body that propagates toward the fingertip with a time delay.

Oscilloscopes are most often used to “test the tester” in ESD pulse test setups, confirming that the pulse from the ESD gun is the right shape and meets the requirements of the standard to which the device is being tested. A typical calibration test setup is shown in Figure 1. The pulse from the ESD gun is fired directly into a current shunt target connected to the oscilloscope through an attenuator required to keep the signal within the limits of the oscilloscope’s 50 Ω input, which is used for this testing. Then, key parameters of the ESD pulse are measured per one of several standards, such as IEC 61000-4-2.  

ESD standards require a range of measurements. The most common are the initial edge 10% to 90% rise time, peak amplitude, pulse width, amplitude and current levels at specified times from the initial edge (e.g., T1 and T2), and time to half value. 

Following are four, important things to do to make sure you get the best ESD pulse measurements from your oscilloscope.

The Periodic Table of Oscilloscope Tools: Analyze (Part III)

We're nearing the end of our tour of the Periodic Table of Oscilloscope Tools, our way of presenting our broad palette of oscilloscope tools in a concise, clear fashion. In this installment, we'll finish up the Analyze grouping, by far the largest on the Periodic Table.

Dynamic Range, Signal Integrity, and ESD Pulses

Figure 1: Use your oscilloscope's full vertical range to
take full advantage of the ADC's resolution

Having considered the impact of sampling rate on ESD pulse measurements, let's now turn our attention to dynamic range and signal integrity. No matter what oscilloscope you use, it's important to make the most of the instrument's full vertical range to achieve maximum accuracy.

How Does Sampling Rate Affect ESD Pulse Measurements?

Figure 1: Characterization of an ESD pulse's rise time
depends largely on the oscilloscope's sampling rate

In continuing our look at ESD/EMC pulse measurements, it would be useful to consider how sampling rate figures into the equation. What sort of sampling rate makes sense to use for capturing an ESD pulse? The answer to that question depends primarily on your pulse's rise time.

Why IEEE's Pulse Definitions and ESD Pulses Don't Mix

Figure 1: The IEEE's pulse definitions, which don't fit
the bill for measuring ESD pulses

The IEEE's pulse definitions, found in the organization's Std 181-2011 that covers transitions, pulses, and related waveforms, set the bar for how pulse measurements are determined. These definitions, which are in the DNA of all oscilloscopes, are just the thing for measuring repetitive pulses such as clock signals but not so much for ESD/EMC measurement requirements. In this post, we'll discuss why that is and what you should do differently for measuring ESD pulses.

Making EMC/ESD Pulse Measurements

Figure 1: Oscilloscopes are used for
testing in the green-shaded boxes

There are many circumstances in which electromagnetic compatibility (EMC) and electrostatic discharge (ESD) testing are a fact of life. Many countries have adopted IEC international standards that dictate certain levels of immunity, as have the automotive, medical, military, and aerospace industries. In this post, we'll begin looking at how oscilloscopes figure into tests for both radiated and conducted EMC/ESD immunity.

Eliminate Pitfalls of DDR Memory Testing

Figure 1: DDR test configuration
for a desktop computer

Since its inception as a standard in the mid 1990s, dual data-rate (DDR) SDRAM memory has been near ubiquitous in computing applications. Compared to single data-rate SDRAM, the DDR SDRAM interface makes higher transfer rates possible by more strict control of the timing of the electrical data and clock signals.